Product from Japan made of high quality aluminum. Made by Nielex. Learn More

Clutch bracket reinforcement gusset by Nielex for NC (2006-2015) Mazda Miata/MX-5. In the NC Miata, the brackets for the pedals were made slightly weaker than those on the preview generation Miatas (NA/NB). Overtime the clutch pedal tends to see some play and feel sloppy on the foot. With the gussets, it strengthens the areas prone to failure and gets rid of any play. It will allow for smoother strokes of the pedal and become a lot easier to feel the biting point on the clutch. Having a lot more information being sent through your foot is crucial during track driving and will give you a lot more confidence during spirited drives. This is a three piece set and is made out of SPC that is 2.3 t thick. Installation requires welding so it is recommended to bring to a professional. Learn More

Made in Japan, the Nielex Front Fender Brace improves the front rigidity of your NC1 & NC2 MX-5 (2006-2012) Roadster. When combined with chassis stiffening and the Nielex Front Strut Bar, your roadster’s body becomes even more rigid and stability is dramatically improved at high speed and when cornering. The best part is the rust-proof kit is 100% bolt-on and easy to install. Learn More

Product made by Nielex. The original front knuckles lack the sufficient hardness of the lengthwise direction in the structure. The drivers feel that the strength of the handling is not good enough especially when they drive in cornering at the high-speed because the deflection of the knuckles is very obvious. Nielex thought up the Front Knuckle Arm Support in order to solve these problems. While we were developing this new product, we were able to get advices from Mr. Oda who used to work for Mazda for a long time and were in charge of the development of chassis and suspension of Mazda's sports cars. Once the driver installs this product, I can say that everybody can feel the wonderful effect. It can be felt even during the low-speed drive. The most impressive effect can be felt when a car runs at over 140km/h, and the driver can feel that the handling gets more stable. NA with ABS : you will need to re-route the cable of the ABS sensor. Learn More

The Nielex Excellent Tower Bar for NC (2006-2015) has been around for a while and they just released their Version-II. Back when they released the Version1, the angles for cutting the mounting points in stainless steel couldn’t be obtained in 3D (too difficult), but now it’s totally possible. The Version2 now has exceptional rigidity and does not have any bending making it extremely rigid. The stainless steel material also gives it a very exotic/luxury look. The 8-point tower bar reinforces 8 different points and improves torsional rigidity vertically and horizontally. Its trapezoidal form also provides maximum support to the sides and prevents twisting and displacement in the engine bay. Lightweight and easy to bolt on, it can be installed in an hour with no drilling required!Please note that fitting this to a NC2 or NC3 will require removal of sound enhancer tube. Learn More

This shift knob was designed based on the M2-1002 factory shift knob, but with heavier weight in mind. It’ll make shifting easier and feels REALLY good. It qill fit all years Mazda MX-5 Miatas. Learn More

Beautiful license plate holder kit made by Nielex of Japan for NC1 and NC2/NC3 MX-5. This kit is of impeccable quality, typical of Nielex. Made of stainless steel and brass, this kit will relocate your front number plate to the side and about 50mm lower. Further, the bracket has a slight curve to it that matches the lines of the Miata. Learn More

Classic looking oil filler cap made by Nielex for your NC (2006-2015) or ND (2016+) Miata. This oil cap is made to the similar specs as the one we could find in the past in the M2-1002 vehicles. It has a beautiful polished top and very detailed side grip pieces. It's an artsy piece for those who pay attention to detail of their engine bay! Learn More

Nielex made the NC Magical Cross right after testing the 2006 MX-5 at high speed and concluded that it needed improvement for high speed cornering. They did not see NC as evolution from NA and NB and wanted to create the perfect chassis stiffness. As a result, they made a Magical Cross for it and now it’s a very popular product in Japan (most Japanese tuners use this product). It improves steering responsiveness and also helps keep tires to the ground for much more traction during cornering. It also reduces frame twist drastically to have a more stable and neutral car. It basically transforms the car into a real fun go kart that you can enjoy driving in the streets or at the track. It is even more effective when combined with the Pro-Spec Knuckle Arm Support! Learn More